Contact Us

ES Industrial Solutions
#171, Thamini Towers
Subban Chetty Street
Theni - 625531.

  •  +91 9940 83 5257 /+91 9443 23 1113

Eccentric Bushing GP100 Metso

ESIS, the Manufacturer, Exporter & Importer and Suppliers of "Eccentric Bushing GP100 Metso" Cone Crusher Wear Parts. We provide and Supply High Quality and High Grade of Eccentric Bushing GP100 Metso the Genuine Cone Crusher Spare parts

Eccentric Bushing GP100 Part Number: 171551, the new Manufactured part to suit Metso Nordberg GP100 Cone Crusher.

Eccentric Bushing Metso Nordberg GP100 is Interchangeable with OEM part 171551 to Metso Nordberg GP100 Cone Crusher.

  • Manufactured for Quarry & Mining Services.
  • Purchased as 'job lot' from liquidators.

ESIS offers following Metso Nordberg GP100 Cone Crusher Bronze Parts

Description Part Number
Nordberg GP100 Eccentric Bushing E20 171551
Nordberg GP100 Eccentric Bushing E25 171564
Nordberg GP100 Eccentric Bushing E16 171565
Nordberg GP100 Frame Bushing 285062
Nordberg GP100 Thrust Bearing 941532
Nordberg GP100 Pressplate 285064

Proper maintenance helps to avoid burning out your cone crusher's eccentric bushing

In a crushing plant, failures may occur, requiring a crusher to be shut down for unscheduled maintenance. Once these stoppages happen, certain precautions need to be taken to avoid repeated occurrence.

Unscheduled stoppages

One possible failure is the burnout of the eccentric bushing. Generally, three conditions will indicate that there has been a bushing burnout:

Total lockup of the crusher

  • Overheating of the lubricating oil
  • Bronze filings in the screen of the hydraulic unit

A few factors that can cause eccentric bushing burnout are:

  • Use of improper lubricating oil
  • A failure in the lubricating system (oil pump)
  • Improper liner configuration
  • Use of inferior quality liners
  • Closed side setting (CSS) too small
  • Off-center or segregated feed
  • Excess fines in feed material
  • Incorrect rotation

What should be done when a bushing burnout occurs?

First, it is necessary to identify the main cause of the failure to know which actions can be taken to avoid the same problem in the future. Then the damaged bushing must be removed immediately so that a new one can be installed.

A few precautions should be taken: when the bushing becomes ‘seized’ (stuck) to the main shaft of the equipment (see picture below), it must be cut for removal.

Caution: Take care not to cause scoring (etching) to the main shaft when you are cutting the bushing.

What is the next step?

Next, it is necessary to clean and polish the main shaft and the inner diameter of the eccentric.

Following clean-up, it is necessary to measure the main shaft and the internal diameter of the eccentric at a minimum of four heights and two positions separated by 90 degrees from each other, as seen in the following example (picture below).

After taking these measurements, they must be submitted to Metso’s technical assistance to assess whether they are within tolerance limits.

If so, the new bushing may be installed. If not, Metso will advise on the type of repair that is possible or whether one of the two components must be replaced. Installation will be performed according to the instructions in the equipment manual.

Prior to resuming normal equipment operation, it will be necessary to “break in” the bushing as established below:

  • Run the crusher free of any load for 1 hour
  • Run the crusher for 2 hours with a full chamber, but with the equipment open far enough to reach 50% of the motor’s nominal power rating (or 60% of its nominal amperage)
  • Close the crusher until 75% of the crusher’s nominal power rating is reached (or 80% of its nominal amperage) and run for another 4 hours
  • Close the crusher until 100% of the nominal amperage is reached and run for 1 hour
  • Between these four steps, always inspect equipment to ensure that operating conditions are normal and that the adjustment ring is not “knocking” during crusher operation.

Tip:All crusher bushings should be inspected at the time of liner replacement. This precaution can help to avoid unexpected stoppages of your equipment.

  • Availability: Pre-Order

Specifications of Eccentric Bushing Metso Nordberg GP100

  • Eccentric Bushing Metso Nordberg GP100 have High level surface finish
  • No burrs and sharp edges in Eccentric Bushing Metso Nordberg GP100
  • Maximum tin content makes Eccentric Bushings Metso Nordberg GP100, stronger and long lasting
  • OEM is available by your drawings, we promise to strictly make it as your request
  • Precise dimension and processing make sure Eccentric Bushing Metso Nordberg GP100 part is perfect in every way
  • Eccentric Bushings Metso Nordberg GP100 the Cone Crusher spare parts are made of good raw material
  • Eccentric Bushings Metso Nordberg GP100 are Inspected and checked with proper Quality Control
  • Eccentric Bushings Metso Nordberg GP100 packed in non-fumigation plywood.
  • 100% testing done before the delivery of Eccentric Bushing Metso Nordberg GP100.
  • Eccentric Bushing Metso Nordberg GP100 are Produced as drawings and requirement strictly.

Write Review on Eccentric Bushing GP100 Metso

Note: Do not use HTML in the text.